RocNetNode

Content → Command Stations → RocNet

• RocNet Protocol | RocNetNode
  • RocNetNode Setup | RocNetNode Configuration | Installer package
• Raspberry Pi Boards
  • GCA-Pi01 | Pi01Can | GCA-Pi02 | GCA-PI03 | GCA-PI04 | GCA-Pi05 | GCA-Pi06 | GCA-PI07 | GCA107 Relay board | RocDisplay | Fast Clock | LED driver Pi08
• Build from source | RasPi as Rocrail server
• FAQ's
• Setup ESpeak (DE) | Setup Sound (DE)

The overview in better resolution

The RocNetNode with its boards is a complete DIY Control System based on commonly used hardware standards.
It can be used for controlling:

• Mobile decoders; Trains.
• Switches, Multi aspect signals, FiddleYards, Turntables, Servos, Daylight…
• Feedback, Occupancy, Inputs…

• The well known I2C standard is used as bus between all GCA-Pi boards.
  
• A standard Ethernet LAN is used as connection between Rocrail and the RocNetNodes.
  
• The Open Source RocNet Protocol is used to communicate with Rocrail.
  

The popular 'credit-card-sized' computer is used as base of the RocNetNode.

• Raspberry Zero
• Raspberry Pi 1, 2 and 3

The Raspberry Pi 4 is currently not supported.

It can be used as software command station too, using DCC232 or SPROG.
“Raspberry Pi" is a trademark of the Raspberry Pi Foundation.

5V 3A Power supply and patch panel. (Preferred over power adapters.)

The interface between the Raspberry Pi and the I2C bus.

32 programmable I/O ports with MACRO support for signal aspects.
It is compatible with all GCA interface boards.
The GCA-107 Multi purpose Relay board can be used for frog polarization.

16 PWM ports for controlling servos, LEDs…
The GCA77 can be connected for max 24V 500 mA dc per port.
Even higher values in dc are possible with GCA76
Both buffer boards are each able of dimming 8 independent outputs.

A hand held throttle with 28 functions at hand.

Zero loss current detection.
Due to some no longer available parts, this unit is no longer available, see GCA94 instead.

Giling Computer Applications

All boards are accepting RJ45 and/or RJ12 connectors.
The RJ45 connector can be used with CAT-5 patch cables.
The RJ12 compatible cables are commonly used by Digitrax LocoNet® and Lenz Xpressnet systems.

The data cable should not be connected to the 5V+.

A very comfortable Configuration utility is provided in Rocrail.
Updating a RocNetNode is done with just a single mouse click.

• No firmware needed, just plain Linux-C and Rocrail libraries.
• RocNet UDP Multicast
• 128 I/O ports.
• Delayed off inputs for occupancy detectors.
• Pulse timed outputs with off event.
• Blink function for outputs.
• Loco and Function commands.
• POM
• Command Station support:
  • DCC232 & ORD3
  • SPROG
• Shutdown event on kill; Rocrail will power off and stop all trains.
• Send every second an identification message until it is acknowledged. This procedure is restarted after the host reported a shutdown.
• Start of Day support. After an identify acknowledge the current input status will be broadcasted.
• Sensor acknowledge; Ten times retry every 500ms.
• Save the output state on "global power off" for restoring them at restart of the RocNetNode.
• Nodes which identify itself with ID 65535 receive automatically an ID in the normal range: 2…65534.
• 128 macros with max. 8 commands each.
• One click software update.
• 128 PWM channels for servos, signals and lighting.
  • Max. 11 minutes for 4096 steps. (steps=1, delay=15)
  • Servo support incl. Fine Tuning and Frog Polarization with the GCA107 Relay board.
• RocMouse support.
• A RasPi/RocNetNode can be mounted in a large scale locomotive when using a USB-WiFi stick for reporting the RFID tags, controlling the decoder with a S-Nano and offers 128 I/O.

The addressing is linear: FADA
Only the Bus(ID) and the Address(RasPi Port) fields are used.

1. DCC232 / SPROG
   • Bus → RocNetID (Or default Loco Bus.)
   • Address → addrH + addrL
2. Node (RasPi in G-Loco)
   • Bus → 0
   • Address → RocNetID

• Bus → RocNetID
• Address → Port (1…128)

• Bus → RocNetID
• Address → Address (FADA)
• Type → DCC, MM, …

• Bus → RocNetID
• Address → Port (1…128)
• Single gate
• Port type:
  • Digital port: Switch or Accessory
  • PWM channel: Servo

• Bus → RocNetID
• Address → Port (Pi02: 1…128, Pi07: 129-160)

Signal aspect numbers are mapped to Macros:

• Bus → RocNetID
• Address-1 → Macro port offset
• Aspect → Macro number (1…32)

• Bus → RocNetID
• Address → Macro number (1…32)
• Parameter → Macro number (1…32) for the Off command in case set > 0

• Bus → RocNetID
• Address → PWM Channel (1…128)
• Value → Brightness (0…255), this value will be multiplied by 16 in RocNetNode.

• Bus → RocNetID
• Address → Not used
• Color channel RGBWW → PWM Channel (1…128); Both white channels are optional and can be set to zero to disable them.
• Value → Brightness (0…255), this value will be multiplied by 16 in RocNetNode.

• Servo switch with Frog polarisation

• Signal aspects with macros

• Turntable multiport