Innovative Model Railroad Control System

User Tools

Site Tools

Trace: • cs-protocol-fr
mvtrack-setup-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
mvtrack-setup-en [2023/10/19 14:00] – created - external edit 127.0.0.1mvtrack-setup-en [2025/06/01 10:47] (current) – [Calibrate] babbel
Line 54: Line 54:
 {{:mvtrack-import.png}}\\ {{:mvtrack-import.png}}\\
 =====Calibrate===== =====Calibrate=====
-If activated the selected loco will get informed of the measured kmh and will adjust its CV 5 value to match the wanted __**[[:loc-calibrate-en#max._km_h|Max. km/h]]**__. \\+If activated the selected loco will get informed of the measured kmh and will adjust its CV 5 / CV 6  value to match the wanted __**[[:loc-calibrate-en#max._km_h|Max. km/h]]**__. \\
 Multiple runs at the highest speed step are necessary to come close to the wanted result.\\ Multiple runs at the highest speed step are necessary to come close to the wanted result.\\
-Depending on the hight of the difference between Vtarget and Vactual, CV5 will be varried.\\+Depending on the hight of the difference between Vtarget and Vactual, CV will be varried.\\
 If the used sensors will report a loco __**[[:loc-gen-en#code|Code]]**__ this will overwrite the selected loco ID in this dialog. (RailCom, RFID, ...)\\  If the used sensors will report a loco __**[[:loc-gen-en#code|Code]]**__ this will overwrite the selected loco ID in this dialog. (RailCom, RFID, ...)\\ 
 +This also applies when the reference block is occupied. \\
 +
 +===none===
 +
 +Disables calibration.
 +
 +===Max:===
 +
 +Enables calibration for CV5.
 +
 +===Mid.===
 +
 +Enables calibration for CV6.
 +
 +
 +
 > Note 1: The CV 5 will be adjusted by a POM write command. > Note 1: The CV 5 will be adjusted by a POM write command.
 > Note 2: The CV 6 will be set by POM to 30% of the CV 5 value. (This percentage can be adjusted on the Loco Calibrate Tab.) > Note 2: The CV 6 will be set by POM to 30% of the CV 5 value. (This percentage can be adjusted on the Loco Calibrate Tab.)
Line 89: Line 105:
 ===== Loco ===== ===== Loco =====
 Selection of an Loco ID for the option **[[#calibrate|Calibrate]]** and if at the option **[[#calculate_train_length|Calculate train length]]** the function **[[#take_measured_value_as loco_length|Take measured value as loco length]]** may  be activated. \\ Selection of an Loco ID for the option **[[#calibrate|Calibrate]]** and if at the option **[[#calculate_train_length|Calculate train length]]** the function **[[#take_measured_value_as loco_length|Take measured value as loco length]]** may  be activated. \\
 + \\
 +
 +===== Block =====
 +Block reference of a Loco ID for the option **[[#calibrate|Calibrate]]** and if at the option **[[#calculate_train_length|Calculate train length]]** the function **[[#take_measured_value_as loco_length|Take measured value as loco length]]** may  be activated. \\
  \\  \\
  
mvtrack-setup-en.1697716846.txt.gz · Last modified: 2023/10/19 14:00 by 127.0.0.1