Differences

This shows you the differences between two versions of the page.

--- mgv101v2-en [2025/08/30 14:56] – rjversluis
+++ mgv101v2-en [2025/08/30 15:38] (current) – rjversluis
@@ Line 1: / Line 1: @@
-====== GCA101v2: LocoBuffer-UDP ======
+====== GCA101v2: LocoBuffer TCP/UDP ======
 [[english|{{  rocrail-logo-35.png}}]]
 [[english|Content]] -> [[hardware-en|Hardware]] -> [[hardware-en#locoio|GCA]]
@@ Line 5: / Line 5: @@
 |< >|
-|  {{::img_1254.jpg?480}}  |
+|  {{::img_1254.jpg?480}}  ||
-^  Hardware by Peter Giling  ^
+^ Hardware ^ Peter Giling |
+^ Firmware TCP ^ Dani Guisado |
+^ Firmware UDP ^ Robert Evers & Fred Jansen |
  \\
@@ Line 88: / Line 90: @@
  \\
+==== LED Signaling====
+^  LED  ^  Function  ^  Remark  ^
+|  1  | Power supply indication  |   |
+|  2  | 3.3 Volt power indication  |   |
+|  3  | LocoNet activity  |   |
+|  4  | Ethernet activity  | Continues blinking means waiting for connection  |
+\\
 ==== Jumper settings ====
@@ Line 109: / Line 120: @@
 Firmware is developed in Spain by Dani Guisado and downloadable here:  https://github.com/ClubNCaldes/GCA101LbServer  \\
 Website of Dani is also very interesting  : http://www.clubncaldes.com/ \\
-Leds blink when waiting for a connection from Rocrail.\\
+LEDs blink when waiting for a connection from Rocrail.\\
-When Rocrail is connected, Led2 and 3 show Loconet activity (send and receive) and led4 Ethernet activity.\\
+When Rocrail is connected, LED 2 and 3 show LocoNet activity (send and receive) and LED 4 Ethernet activity.\\
 Standard Ethernet address: 192.168.0.200.\\
 Other IP addres can be pre-programmed in INO file before programming the chip.\\
@@ Line 123: / Line 134: @@
 === Rocrail setup ===
 Communication needs to be set as LbServer in Rocrail settings > controller:\\
-{{:gca:controller_setting.jpg}}
+{{:gca:gca101-tcp-setup-en.png?400}}
-=== LED Signalling===
-^  GCA101v2 board  ^^^
-|  LED1  |  supply power indication  |   |
-|  LED2  |  3.3 Volt power indication  |   |
-|  LED3  |  Loconet activity  |   |
-|  LED4  |  Ethernet activity  |  continue blinking means waiting for connection  |
-\\
 ==== UDP ====
-[[http://en.wikipedia.org/wiki/User_Datagram_Protocol|{{  http://upload.wikimedia.org/wikipedia/de/8/80/UDP.PNG}}]]
+=== Files ===
 {{:mgv:hardware:gca101v2.1.0.6.zip|This is the most recent .hex file for U1}}
-Thanks to Robert Evers & Fred Jansen who have put much energy in getting the system up and running, you will finally be able to run Rocrail and Loco-I/O without USB and/or RS232.\\
-=== Led signalling===
-^  GCA101v2 board  ^^^
-|  LED1  |  supply power indication  |   |
-|  LED2  |  3.3 Volt power indication  |   |
-|  LED3  |  Loconet activity  |   |
-|  LED4  |  Ethernet activity  |  continue slow blinking means waiting for connection  |
-\\
 === Rocrail Setup===