arduino:wio-setup-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
arduino:wio-setup-en [2025/05/26 09:25] – [CVs] rjversluis | arduino:wio-setup-en [2025/05/29 09:05] (current) – [CVs] rjversluis | ||
---|---|---|---|
Line 354: | Line 354: | ||
\\ | \\ | ||
- | =====OTA from Scratch===== | + | ====OTA from Scratch==== |
To avoid bothering with the needed libraries for the WIO Sketch this {{: | To avoid bothering with the needed libraries for the WIO Sketch this {{: | ||
( The Sketch can also be downloaded from https:// | ( The Sketch can also be downloaded from https:// | ||
Line 375: | Line 375: | ||
\\ | \\ | ||
+ | < | ||
+ | =====Files===== | ||
+ | File management for WIO CAN.\\ | ||
+ | |||
+ | |||
+ | \\ | ||
+ | < | ||
=====I/O Mapping===== | =====I/O Mapping===== | ||
{{: | {{: | ||
Line 400: | Line 407: | ||
\\ | \\ | ||
+ | < | ||
=====User CV===== | =====User CV===== | ||
====Interface==== | ====Interface==== | ||
Line 424: | Line 432: | ||
|< >| | |< >| | ||
^ CV# ^ Description ^ Range ^ Default ^ PicoW ^ ESP32 ^ ESP8266 ^ Remark ^ | ^ CV# ^ Description ^ Range ^ Default ^ PicoW ^ ESP32 ^ ESP8266 ^ Remark ^ | ||
- | | 0 | LED_ShowMode | 0=off, 1=on | 1 | | + | | 0 | LED_ShowMode | 0=off, 1=on | 1 | | | | Show onboard LED flashing to show operation mode | |
- | | 1 | User_Sound | 0=off, 1=on | 0 | | + | | 1 | User_Sound | 0=off, 1=on | 0 | | | | User sound over DAC | |
| 2 | Bat_2S_Full | | 2 | Bat_2S_Full | ||
| 3 | Bat_2S_Empty | 0...4095 | | 2220 | 1670 | 480 | | | 3 | Bat_2S_Empty | 0...4095 | | 2220 | 1670 | 480 | | ||
Line 432: | Line 440: | ||
| 6 | Bat_4S_Full | | 6 | Bat_4S_Full | ||
| 7 | Bat_4S_Empty | 0...4095 | | 3200 | 3090 | 760 | | | 7 | Bat_4S_Empty | 0...4095 | | 3200 | 3090 | 760 | | ||
- | | 8 | Servo_Min_Pulse | 500...1000 | 700 | | + | | 8 | Servo_Min_Pulse | 500...1000 | 700 | | | | Check used servo types for the right value | |
- | | 9 | Servo_Max_Pulse | 2000...2500 | 2300 | | + | | 9 | Servo_Max_Pulse | 2000...2500 | 2300 | | | | Check used servo types for the right value | |
| 10 | Display_Keypad_Line | 0...7 | 2 | | | 10 | Display_Keypad_Line | 0...7 | 2 | | ||
| 11 | Stepper_ISR_US | | 150 | | | | Number of micro seconds for timer interrupt | | | 11 | Stepper_ISR_US | | 150 | | | | Number of micro seconds for timer interrupt | | ||
| 12 | Stepper_ISR_Accel | | 50 | | | | Start/end delay (number of steps for accelerate and decelerate) -> range | | | 12 | Stepper_ISR_Accel | | 50 | | | | Start/end delay (number of steps for accelerate and decelerate) -> range | | ||
| 13 | Stepper_ISR_Accel_Step | | 15 | | | | Number of ticks before add/ | | 13 | Stepper_ISR_Accel_Step | | 15 | | | | Number of ticks before add/ | ||
+ | | 14 | User_altitude | | 104 | | | | https:// | ||
arduino/wio-setup-en.1748244346.txt.gz · Last modified: 2025/05/26 09:25 by rjversluis